View T-51513D104J-FW-A-AD_908036.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Type No.
w
w
w
.D
at
. LCD Module Technical Specification U t4 ee T-51513D104J-FW-A-AD Sh a
om c
First Edition
Dec 23, 2004
Final Revision
******
Approved by (Quality Assurance Division)
Checked by (ACI Engineering Division)
Prepared by (ACI Engineering Division)
No. -1 2 3 4 5 6 7 8 9 CONTENTS APPLICATION OVERVIEW
Item
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS INTERFACE PIN CONNECTION INTERFACE TIMING BLOCK DIAGRAM
MECHANICAL SPECIFICATION
w
11 12 ----
10
w
OPTICAL CHARACTERISTICS RELIABILITY TEST CONDITION INSPECTION STANDARDS HANDLING PRECAUTIONS FOR TFT-LCD MODULE PACKAGING SPECIFICATION PRODUCTS NUMBER LABELING FORMS LAMP UNIT FOR 10.4" VGA
w
.D
t a
S a
e h
t e
U 4
.c
m o
Page 1 2 3 4 4 7 8 12 13 15 17 18 19 22 25
27
T-51513D104J-FW-A-AD (AD) No. 2004-0193
OPTREX CORPORATION
w
w
w
.D
at
Sh a
et e
4U
.
om c
Page 1/32
1. APPLICATION
This specification applies to color TFT-LCD module, T-51513D104J-FW-A-AD. These specification papers are the proprietary product of OPTREX and include materials protected under copyright of OPTREX. No part of this document may be reproduced in any form or by any means without the express written permission of OPTREX. OPTREX does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a product specified in this document. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of OPTREX or of others. OPTREX classifies the usage of the TFT-LCD module as follows. Please confirm the usage before using the product. (1) Standard Usage Computers, office equipment, factory automation equipment, test and measurement equipment, communications, transportation equipment(automobiles, ships, trains, etc.), provided, however, that operation is not influenced by TFT-LCD directly. (2) Special Usage Medical equipment, safety equipment, transportation equipment, provided, however, that TFT-LCD is necessary to its operation. (3) Specific Usage Cockpit Equipment, military systems, aerospace equipment, nuclear reactor control systems, life support systems and any other equipment. OPTREX should make a contract that stipulate apportionment of responsibilities between OPTREX and our customer. The product specified in this document is designed for "Standard Usage" unless otherwise specified in this document. If customers intend to use the product for applications other than those specified for "Standard Usage", they should contact OPTREX sales representative in advance. OPTREX has been making continuous effort to improve the reliability of its products. Customers should implement sufficient reliability design of their application equipments such as redundant system design, fail-safe functions, anti-failure features. OPTREX assumes no responsibility for any damage resulting from the use of the product that does not comply with the instructions and the precautions specified in this document. Please contact and consult a OPTREX sales representative for any questions regarding this product.
T-51513D104J-FW-A-AD (AD) No. 2004-0193
OPTREX CORPORATION
Page 2/32
2. OVERVIEW
T-51513D104J-FW-A-AD is 10.4" color TFT-LCD (Thin Film Transistor Liquid Crystal Display) module composed of LCD panel, driver ICs, control circuit, and backlight unit. By applying 6 bit digital data 640 x 480, 260K-color images are displayed on the 10.4" diagonal screen. Input power voltages are 3.3 / 5.0V for LCD driving. The type of data and control signals are digital and transmitted via CMOS interface per Typ. 25 MHz clock cycle. Inverter for backlight is not included in this module. General specifications are summarized in the following table: ITEM Display Area (mm) Number of Dots Pixel Pitch (mm) Color Pixel Arrangement Display Mode Number of Color Brightness (cd/m2) Wide Viewing Angle Technology Viewing Angle (CR 10) Surface Treatment Electrical Interface Optimum Viewing Angle(Contrast ratio) Module Size (mm) Module Mass (g) Backlight Unit SPECIFICATION 211.2(H) x 158.4 (V) (10.39-inch diagonal) 640 x 3 (H) x 480 (V) 0.33 (H) x 0.33 (V) RGB vertical stripe Normally white TN 260K 430 Optical compensation film -6565 (H) -65~45 (V)
Anti-glare and hard-coating 3H CMOS 6 o'clock 243.0 (W) x 181.6 (H) x 12.2 (D) 540 CCFL, 2-tubes, edge-light, replaceable
Characteristic value without any note is typical value.
T-51513D104J-FW-A-AD (AD) No. 2004-0193
OPTREX CORPORATION
Page 3/32
3. ABSOLUTE MAXIMUM RATINGS
ITEM Power Supply Voltage for LCD Logic Input Voltage Lamp Voltage Lamp Current Lamp Frequency Operation Temperature (Panel) Operation Temperature (Ambient) Storage Temperature
Note 1,2) Note 2) Note 2)
SYMBOL VCC VI VL IL FL Top(Panel) Top(Ambient) Tstg
MIN. -0.3 0 0 0 30 -20 -20 -20
MAX. 6.5 6.5 1500 10.0 80 70 70 80
UNIT V V Vrms mArms kHz C C C
[Note] 1) Measured at the center of active area and at the center of panel back surface 2) Top,Tstg 40C : 90%RH max. without condensation Top,Tstg > 40C : Absolute humidity shall be less than the value of 90%RH at 40C without condensation.
4. ELECTRICAL CHARACTERISTICS
(1) TFT- LCD ITEM Power Supply Voltage for LCD Power Supply Current for LCD Logic Input Voltage t1 10 ms 0 < t2 50 ms 0 < t3 50 ms
0.9VCC
LCD Power Supply Logic Signal
Ambient Temperature : Ta = 25C
SYMBOL
MIN. 3.0 4.75 2.0 0
TYP. 3.3 5.0 300 200 -
MAX. 3.6 5.25 450 300 100 5.25 0.8
UNIT V V mA mA mVp-p V V
Remarks *1) *1) *2) *2) VCC = +3.3V/5.0V
3.3V powered 5.0V powered 3.3V powered 5.0V powered High Low
VCC VCC ICC ICC VRP VIH VIL
Permissive Input Ripple Voltage
*1) Power and signals sequence: 400 ms t4 200 ms t5 0 t6
VCC 0.9VCC data 0.1VCC 0.1VCC
0.1VCC
t1
t2 VL
t3
t4
Backlight Power Supply
t5 t6 data: RGB DATA, DCLK, HD, VD, DENA
T-51513D104J-FW-A-AD (AD) No. 2004-0193
OPTREX CORPORATION
Page 4/32
VCC-dip conditions: (a) 3.3 V powered 1) When 2.4 V VCC < 3.0 V, td 10 ms 2) When VCC < 2.4 V VCC-dip conditions should also follow the power and signals sequence.
VCC
td
(b) 5.0V powered 1) When 3.6 V VCC < 4.5 V, td 10 ms 2) When VCC < 3.6 V VCC-dip conditions should also follow the power and signals sequence.
VCC
2.4 V
td
*2) Typical current condition: 64- gray- bar-pattern 480 line mode VCC = + 3.3 / 5.0 V, fH=31.5kHz, fV=60Hz, fCLK= 25MHz (2) Backlight ITEM Lamp Voltage Lamp Current Lamp Frequency Starting Lamp Voltage Lamp Life Time SYMBOL VL IL FL VS MIN. -3.0 40 930 1170 1300 LT 50000 TYP. 480 6.0 ----MAX. -7.0 80 -UNIT Vrms mArms kHz Vrms Vrms Vrms h Ta=25C Remarks IL=6.0 mArms *1),*5) *2) Ta = 25C Ta = 0C Ta = -20C *3),*4) IL=6.0mArms Continuous Operation
Page 5/32
3.6 V
----
--
T-51513D104J-FW-A-AD (AD) No. 2004-0193
OPTREX CORPORATION
4.5 V
3.0 V
*1) Lamp Current measurement method (The current meter is inserted in low voltage line.)
CTL CTH
A
LCD Module
CTL CTH
A
Inverter
Power Supply
*2) Lamp frequency of inverter may produce interference with horizontal synchronous frequency, and this may cause horizontal beat on the display. Therefore, please adjust lamp frequency, and keep inverter as far from module as possible or use electronic shielding between inverter and module to avoid the interference. *3) Lamp life time is defined as the time either when the brightness becomes 50% of the initial value, or when the starting lamp voltage does not meet the value specified in this table. *4) The life time of the backlight depends on the ambient temperature. The life time will decrease under low/high temperature. *5) Please use the inverter which has symmetrical current wave form as follows, The degree of unbalance: less than 10% The ratio of wave height: less than 2 10%
IPH IPL
IPH: High side peak IPL: Low side peak
The degree of unbalance = |IPH - IPL| / Irms x 100(%) The ratio of wave height = IPH(or IPL) / Irms
CURRENT WAVE FORM
T-51513D104J-FW-A-AD (AD) No. 2004-0193
OPTREX CORPORATION
Page 6/32
5. INTERFACE PIN CONNECTION
(1) CN 1(Interface Signal) Used connector: DF9B-31P-1V(HIROSE) Corresponding connector: DF9-31S-1V(HIROSE) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Symbol GND DCLK HD VD GND R0 R1 R2 R3 R4 R5 GND G0 G1 G2 G3 G4 G5 GND B0 B1 B2 B3 B4 B5 GND DENA VCC VCC TEST SC Function Clock signal for sampling catch data signal Horizontal sync signal Vertical sync signal Red data signal(LSB) Red data signal Red data signal Red data signal Red data signal Red data signal(MSB) Green data signal(LSB) Green data signal Green data signal Green data signal Green data signal Green data signal(MSB) Blue data signal(LSB) Blue data signal Blue data signal Blue data signal Blue data signal Blue data signal(MSB) Data enable signal (to settle the viewing area) 3.3 / 5.0 V Power Supply 3.3 / 5.0 V Power Supply This pin should be open. Test signal output for only internal test use. Scan direction control (Low or Open=Normal, High=Reverse)
(2) CN 2 , CN 3 (Backlight) Backlight-side connector: BHR-02(8.0)VS-1N(JST) Inverter-side connector: SM02(8.0)B-BHS(JST) Pin No. 1 3 Symbol CTH CTL [Note] VBLH-VBLL=VL
T-51513D104J-FW-A-AD (AD) No. 2004-0193 OPTREX CORPORATION Page 7/32
*) The shielding case is connected with GND
Function VBLH High Voltage VBLL Low Voltage
6. INTERFACE TIMING
(1) Timing Specifications ITEM Frequency DCLK Period Low Width High Width DATA Set up time (R,G,B,DENA Hold time HD, VD) Horizontal Active Time Horizontal Front Porch Horizontal Back Porch DENA Vertical Active Time Vertical Front Porch Vertical Back Porch Frequency HD Period Low Width Frequency VD [Note] 1) DATA is latched at fall edge of DCLK in this specification. 2) Polarities of HD and VD are negative in this specification. 3) DENA (Data Enable) should always be positive polarity as shown in the timing specification. 4) DCLK should appear during all invalid period, and HD should appear during invalid period of frame cycle. 5) tHFP + tHBP 20 tCLK Period Low Width SYMBOL fCLK tCLK tWCL tWCH tDS tDH tHA tHFP tHBP tVA tVFP tVBP fH tH tWHL fV tV tWVL MIN. -34.5 12 12 5 5 640 10 2 480 1 2 27 26.3 5 55 14.3 3 TYP. 25 40 ----640 16 138 480 13 33 31.5 31.7 96 60 16.7 -MAX. 29 -----640 --480 --38 37.0 -70 18.2 -UNIT MHz ns ns ns ns ns tCLK tCLK tCLK tH tH tH kHz
s
tCLK Hz ms tH
T-51513D104J-FW-A-AD (AD) No. 2004-0193
OPTREX CORPORATION
Page 8/32
(2) Timing Chart
a. Pixel Timing Chart
tWCH
tCLK tWCL 2.0V 0.8V
DCLK
tD
tD
DATA(R,G,B), DENA, HD, VD b. Horizontal Timing Chart
DCLK
First Data
DATA (R,G,B)
Invalid Data
1
2
3
639
640
Invalid Data Last Data
tHFP
tHBP
tHA
DENA
tH=1/fH tWHL
HD
c. Vertical Timing Chart
HD
LINE DATA
Invalid Data
1
2
3
479
480
Invalid Data
tVFP
tVBP
tVA
DENA
tV=1/fV tWVL
VD
T-51513D104J-FW-A-AD (AD) No. 2004-0193 OPTREX CORPORATION Page 9/32
(3) Color Data Assignment
INPUT DATA
R DATA G DATA R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B DATA B3 B2 B1 B0
LSB
COLOR
R5
MSB
R4
R3
R2
LSB MSB
LSB MSB
BLACK RED(63) GREEN(63) BASIC BLUE(63) COLOR CYAN MAGENTA YELLOW WHITE RED(1) RED(2) RED RED(62) RED(63) GREEN(1) GREEN(2) GREEN GREEN(62) GREEN(63) BLUE(1) BLUE(2) BLUE BLUE(62)
0 1 0 0 0 1 1 1 0 0
0 1 0 0 0 1 1 1 0 0
0 1 0 0 0 1 1 1 0 0
0 1 0 0 0 1 1 1 0 0
0 1 0 0 0 1 1 1 0 1
0 1 0 0 0 1 1 1 1 0
0 0 1 0 1 0 1 1 0 0
0 0 1 0 1 0 1 1 0 0
0 0 1 0 1 0 1 1 0 0
0 0 1 0 1 0 1 1 0 0
0 0 1 0 1 0 1 1 0 0
0 0 1 0 1 0 1 1 0 0
0 0 0 1 1 1 0 1 0 0
0 0 0 1 1 1 0 1 0 0
0 0 0 1 1 1 0 1 0 0
0 0 0 1 1 1 0 1 0 0
0 0 0 1 1 1 0 1 0 0
0 0 0 1 1 1 0 1 0 0
1 1 0 0
1 1 0 0
1 1 0 0
1 1 0 0
1 1 0 0
0 1 0 0
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 1
0 0 1 0
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
1 1 0 0
1 1 0 0
1 1 0 0
1 1 0 0
1 1 0 0
0 1 0 0
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 1
0 0 1 0
0
0
0
0
0
0
0
0 0
0 0
0 0
0 0
0 0
1 1
1 1
1 1
1 1
1 1
0 1
BLUE(63) 0000000 [Note] 1) Definition of gray scale Color (n) --- n indicates gray scale level. Higher n means brighter level. 2) Data 1:High, 0: Low
T-51513D104J-FW-A-AD (AD) No. 2004-0193
OPTREX CORPORATION
Page 10/32
(4) Display Position and Scan Direction D(X,Y) shows the data number of input signal for LCD panel signal processing PCB. SC: Low or Open
D(1,1) D(640,1)
SC: High
D(640,480) D(1,480)
CN2
CN2
D(1,480)
D(640,480)
CN3
D(640,1)
D(1,1)
CN3
T-51513D104J-FW-A-AD (AD) No. 2004-0193
OPTREX CORPORATION
Page 11/32
7. BLOCK DIAGRAM
Timing signal Display data
Timing Converter
G1
Driver(gate)
I/F Connector
G2
TFT-LCD
G480 S1919 S1920
Page 12/32
Power
S1 Power Supply Circuit BACKLIGHT CN2, 3 1 3 CCFL
T-51513D104J-FW-A-AD (AD) No. 2004-0193
Driver(source)
OPTREX CORPORATION
S2
8. MECHANICAL SPECIFICATIONS
(1) Front Side
(Unit:mm)
T-51513D104J-FW-A-AD (AD) No. 2004-0193
OPTREX CORPORATION
Page 13/32
(2) Rear Side
[Note] We recommend you referring to the detailed drawing for your design. Please contact our company sales representative when you need the detailed drawing.
T-51513D104J-FW-A-AD (AD) No. 2004-0193 OPTREX CORPORATION
(Unit:mm)
Page 14/32
9. OPTICAL CHARACTERISTICS
Ta=25C, VCC=3.3 / 5.0 V, Input Signals: Typ. Values shown in Section 6
ITEM Contrast Ratio Luminance Luminance Uniformity Response Time Horizontal Viewing Angle Vertical Horizontal Vertical Image Sticking Red Color Coordinates Blue White Green
SYMBOL CONDITION CR Lw
Lw = = 0 = = 0 = = 0 = = 0 = = 0
MIN. 350 340 ----5050 -4030 -6565 -5040 -0.555 0.304 0.300 0.506 0.138 0.143 0.300 0.312
TYP. 500 430 -10 30 -6565 -6545 -8080 -8050 -0.585 0.334 0.330 0.536 0.168 0.173 0.330 0.342
MAX. --30 ------2 0.615 0.364 0.360 0.566 0.198 0.203 0.360 0.372
UNIT -cd/m2 % ms ms
Remarks *1)*2)*6) *1)*3)*6) *1)*4)*6) *1)*5)*6) *1)*5)*6) *1)*6) *1)*6) *1)*6) *1)*6)
tr tf

CR 10 CR 5 2h
tis Rx Ry Gx Gy Bx By Wx Wy
s
*7)
= = 0
--
*1)*6)
[Note] These items are measured using CS1000(MINOLTA) for color coordinates, EZContrast(ELDIM) for viewing angle and CS1000 or BM-5A(TOPCON) for others under the dark room condition (no ambient light) after more than 30 minutes from turning on the lamp unless noted. Condition: IL=6.0 mArms, FL=55 kHz *1) Measurement Point Contrast Ratio, Luminance, Response Time, Viewing Angle, Color Coordinates: Display Center Luminance Uniformity: point 15 shown in a figure below 160 320 480 (1,1)
120 240 360 3 1 5 4 (640,480) 2
*2) Definition of Contrast Ratio CR=ON (White) Luminance / OFF(Black) Luminance *3) Definition of Luminance Lw= ON (White) Luminance
T-51513D104J-FW-A-AD (AD) No. 2004-0193
OPTREX CORPORATION
Page 15/32
*4) Definition of Luminance Uniformity Lw=[Lw(MAX)/Lw(MIN)-1] x 100 *5) Definition of Response Time
White 90% 90%
Luminance
10% tr
Black
10%
tf
*6) Definition of Viewing Angle( , )
*7) Image Sticking Continuously display the test pattern shown in the figure below for two-hours. Then display a completely white screen. The previous image shall not persist more than two seconds at 25C.
Cols 318-322
White Area Rows 238-242 Black Lines
TEST PATTERN FOR IMAGE STICKING TEST
T-51513D104J-FW-A-AD (AD) No. 2004-0193
OPTREX CORPORATION
Page 16/32
10. RELIABILITY TEST CONDITION
(1) Temperature and Humidity TEST ITEM HIGH TEMPERATURE HIGH HUMIDITY OPERATION HIGH TEMPERATURE OPERATION LOW TEMPERATURE OPERATION HIGH TEMPERATURE STORAGE LOW TEMPERATURE STORAGE THERMAL SHOCK (NON-OPERATION) CONDITIONS 40C, 90%RH, 240 h (No condensation) 70C, 240 h
-20C, 240 h
80C, 240 h
-20C, 240 h
BETWEEN -20C (1h) and 80C(1h), 100 CYCLES
(2) Shock & Vibration ITEM Shock level: 1470m/s2 (150G) SHOCK (NON-OPERATION) Waveform: half sinusoidal wave, 2ms Number of shocks: one shock input in each direction of three mutually perpendicular axis for a total of six shock inputs Vibration level: 9.8m/s2 (1.0G) Waveform: sinusoidal VIBRATION (NON-OPERATION) Frequency range: 5 to 500Hz Frequency sweep rate: 0.5 octave /min Duration: one sweep from 5 to 500 Hz in each of three mutually perpendicular axis(total 3 hours) (3) Judgment standard The judgment of the above tests should be made as follow: Pass: Normal display image, no damage of the display function. (ex. no line defect) Partial transformation of the module parts should be ignored. Fail: No display image, damage of the display function. (ex. line defect) CONDITIONS
T-51513D104J-FW-A-AD (AD) No. 2004-0193
OPTREX CORPORATION
Page 17/32

▲Up To Search▲

Price & Availability of T-51513D104J-FW-A-AD

	To Download T-51513D104J-FW-A-AD Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .